Видео

I bought my car hot wired like this but I’m tired of connecting & disconnecting wires every time I go anywhere or park-how do I get it where I can have a on & off switch inside my car for the fan?

My tcm seems to have issues. Did you find it in the trans ? Is it an expensive fix

Where did you get the shifter knob at?

Fuse locations ? … I’ve read some years have up to 3 different fuses tied into that system… is that true?

This can be done without doing any cutting of the hard lines. Just disconnect the top transmission line (return line) from the radiator and push on the hose right there. No need for any cutting under the car.

did you have trouble with the battery draining ?

I'm late to the Party, Lifter Roller is seizing up. I'm going through that now with a L77. My cam bearings are also making a scratching noise. My band-aid is I changed to redline 10w-60 and 12oz of ZDDP additive and it's silent. Not a fix but it will minimize damage until I can get her fixed up.

sorry but you lost me , ok so you cut the 2 hard tubing lines ? and then you connected each hard line to each black hose ?

Thank you bro! Just subscribed. Had the same issue after hitting a pothole. Going to get it lifted and pull the plastic covering off the bottom of mine (not sure who put it on there? or if its oem) but i appreciate the help

You have link to this cooler?

Do you have to do all this just to replace wheel bearing?>

Man mine the flange doesn’t connect well on the test pipe they supplied

Could have been a good vid…ummm

I'm about to do this myself, bit nervous about the f1 mod

7mm for those that don’t have a 9/32”

that same spoiler is 67 bucks on ebay

you have to buy a base light to make it work - you have a different brake light than a base has and that spoiler is for a base..

Just had the same problem, mine was I think on the red wire but it melted it. Being that it's a 35,000 dollar e85 build and procharged i dont want to take any chances.

👍 YOU ~ ROCK ! ! 🤛

4:05 Do you know the owner of that black base C6? I suspect that may be the car I bought in April 2020. Same wheels, etc.

Replaced mine in about 20 minutes. Once you get the back end up. Drop the gas tank skid Plateon th drivers side. Pop off the linkage....put the new bushing on. Replace the shield....done.

You sir, have been a world of help and it is appreciated!

G@y automatic, well deserved.

Pretty sure I wouldn't let this guy touch my Vette....

When under the hood check for Harmonic Balancer wobble. This is a very common issue on the C6.

Went to a momo flat bottom in my C5. Beautiful

You might consider sticking a wooden golf"T" in the end of the brake hose to keep it from dripping brake fluid on your next go round…..

It's actually significantly better to just upgrade the plug than it is to cut these out and try to crimp/solder it together. The Anderson 879-SBS75GBLK-BK connector with the 1339G3-BK contacts are designed for significantly higher current, thus they will not melt everything when the fan demand is too high

You got the bushing in and back on without dropping the ehaust?

Would this work on a 2010 Malibu with the same type of paddles?

Wonderful, wonderful information and duly noted here.

Good video

Thanks man, I have the same problem with my C6 Z06. Getting ready to get busy on mine. Good luck in the future fellow Vetter

I watched your other video where you ran it with the covers off and I thought that rocker was moving just fine?

I bought my c6 last December and we have the exact same vette same color and everything. I installed a custom carbon fiber front splitter and rear spoiler. I also installed a borla exhaust. I plan on swapping all Powertrain with custom built.

I’ll pay you to finish up my car

I got a DH racing radiator for my 95 c4! All the welds looked really good hopefully I don't have problems with my trans lines

Link for the Trans cooler?

Automatic? C'mon man!

ding ding ding ding ding ding ding ding ding ding ding ding ding ding ding ding ding ding ding ding ding ding ding

Thank you so much! I really appreciate you doing this. So I have a crazy question. I just bought a 2005 c6. Manual. I’m learning. It’s a z51 package. It has all the bells and whistles. I wanted the vettte to have a nice exhaust sound . What do you recommend? I heard a corsa exhaust. I just got it today.I just want it to sound awesome. What are your thoughts on the Bose system? Thank you!!

where did you get the new trans liine?

AND you cut a big rain hole in the hood. Nice

Great video. I plan on using this style seat in my '90 C4 Convertible. Did you use the OEM seatbelts, without any relocation or modification issues ?

Great video I just subscribed 👍🏽

Great walk through nice job 😎

Nice job but thank god for aerosols like S100 engine brightener & Black on Black. That’s what I use…

what corvette forum do you recommend

How fresh is the motor? Odometer is over 200k and still running strong?

Or I can probably go out there to Texas Motor Speedway is there specific track days?